Auto Finesse Desire 150G - Carnauba Wax - Autohub Pakistan

Auto Finesse Desire 150G - Carnauba Wax

  • Rs.18,500


OUR FLAGSHIP CARNAUBA CAR WAX , CAREFULLY BLENDED BY HAND THERE IS NO FINER WAY TO COMPLETE YOUR FLAWLESS FINISH

The Auto Finesse Desire carnauba natural wax is carefully blended by hand in Great Britain and contains 54% T1 Grade Brazilian Carnauba Wax by volume, with the remainder being made up by all natural Beeswax, and oils. These ingredients treat vehicles with nature’s own defense against the elements, giving it water repellency, and resistance to environmental pollution (Including UV-fading, acid rain, and bird droppings.).

It smells of wild berry and has an ultra-high wax solids content, meaning durability of up to 6 months. 

Application:

Before waxing, make sure that the vehicle is clean and cool to the touch. If bonded contamination is present, use a clay bar to prep the surface for best results. If the paintwork is lightly marred, or the vehicle has not been polished in the last 6-12 months, it is also advisable to use one of our signature Pre-Wax Cleansers in order to create the maximum shine. Place a foam applicator inside the pot of wax, and rotate it half a turn to prime the pad with product. This is typically enough wax to protect a single moderately-sized panel, though this may vary depending upon the condition of the paintwork. Apply the wax to the panel with small, overlapping circular strokes, light pressure, and in a consistent pattern to obtain full coverage of the paint. If the applicator feels like it is starting to run dry across the surface, or coverage becomes uneven, return the applicator to the container using another quarter-turn of the pad to re-prime the foam. The goal when waxing is to apply the product as thinly and evenly as possible, since a little bit goes a very long way to protecting and enhancing the shine of your vehicle.

Once you have completed one normal-sized panel, or half of a large one, move on to another section of equal size. When you are done waxing the second section, you will be ready to buff off the wax from the first using a plush microfibre towel. Continue until all panels are complete. Auto-Finesse Desire only takes a few minutes to cure, so take care not to let the product dry onto the surface. If the wax has been allowed to dry, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied.), you can use a water-based quick detailer like Auto-Finesse Finale to help ease removal of the residue. When applying multiple layers of wax for extra depth, wetness and protection, make sure to wait at least 3 hours in between coats.

For best results, do not wax the vehicle if the ambient temperature is below 6 degrees Celsius, or above 35 degrees Celsius. Waxing in direct sunlight, or conditions of high humidity can respectively lead to over, or under-curing of the product before removal.

Related Products

Auto Finesse Desire 150G - Carnauba Wax

Pay Cash On Delivery *

Free delivery **

* Only for Pakistan

** Not valid for tyres or heavy items

Note: Any order above 10 thousand require upfront money using Bank transfer or Easy Paisa

This product is currently sold out.

OUR FLAGSHIP CARNAUBA CAR WAX , CAREFULLY BLENDED BY HAND THERE IS NO FINER WAY TO COMPLETE YOUR FLAWLESS FINISH

The Auto Finesse Desire carnauba natural wax is carefully blended by hand in Great Britain and contains 54% T1 Grade Brazilian Carnauba Wax by volume, with the remainder being made up by all natural Beeswax, and oils. These ingredients treat vehicles with nature’s own defense against the elements, giving it water repellency, and resistance to environmental pollution (Including UV-fading, acid rain, and bird droppings.).

It smells of wild berry and has an ultra-high wax solids content, meaning durability of up to 6 months. 

Application:

Before waxing, make sure that the vehicle is clean and cool to the touch. If bonded contamination is present, use a clay bar to prep the surface for best results. If the paintwork is lightly marred, or the vehicle has not been polished in the last 6-12 months, it is also advisable to use one of our signature Pre-Wax Cleansers in order to create the maximum shine. Place a foam applicator inside the pot of wax, and rotate it half a turn to prime the pad with product. This is typically enough wax to protect a single moderately-sized panel, though this may vary depending upon the condition of the paintwork. Apply the wax to the panel with small, overlapping circular strokes, light pressure, and in a consistent pattern to obtain full coverage of the paint. If the applicator feels like it is starting to run dry across the surface, or coverage becomes uneven, return the applicator to the container using another quarter-turn of the pad to re-prime the foam. The goal when waxing is to apply the product as thinly and evenly as possible, since a little bit goes a very long way to protecting and enhancing the shine of your vehicle.

Once you have completed one normal-sized panel, or half of a large one, move on to another section of equal size. When you are done waxing the second section, you will be ready to buff off the wax from the first using a plush microfibre towel. Continue until all panels are complete. Auto-Finesse Desire only takes a few minutes to cure, so take care not to let the product dry onto the surface. If the wax has been allowed to dry, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied.), you can use a water-based quick detailer like Auto-Finesse Finale to help ease removal of the residue. When applying multiple layers of wax for extra depth, wetness and protection, make sure to wait at least 3 hours in between coats.

For best results, do not wax the vehicle if the ambient temperature is below 6 degrees Celsius, or above 35 degrees Celsius. Waxing in direct sunlight, or conditions of high humidity can respectively lead to over, or under-curing of the product before removal.

comments powered by Disqus

Your cart is empty.

Auto Finesse Desire 150G - Carnauba Wax - Autohub Pakistan

Auto Finesse Desire 150G - Carnauba Wax

  • Rs.18,500


OUR FLAGSHIP CARNAUBA CAR WAX , CAREFULLY BLENDED BY HAND THERE IS NO FINER WAY TO COMPLETE YOUR FLAWLESS FINISH

The Auto Finesse Desire carnauba natural wax is carefully blended by hand in Great Britain and contains 54% T1 Grade Brazilian Carnauba Wax by volume, with the remainder being made up by all natural Beeswax, and oils. These ingredients treat vehicles with nature’s own defense against the elements, giving it water repellency, and resistance to environmental pollution (Including UV-fading, acid rain, and bird droppings.).

It smells of wild berry and has an ultra-high wax solids content, meaning durability of up to 6 months. 

Application:

Before waxing, make sure that the vehicle is clean and cool to the touch. If bonded contamination is present, use a clay bar to prep the surface for best results. If the paintwork is lightly marred, or the vehicle has not been polished in the last 6-12 months, it is also advisable to use one of our signature Pre-Wax Cleansers in order to create the maximum shine. Place a foam applicator inside the pot of wax, and rotate it half a turn to prime the pad with product. This is typically enough wax to protect a single moderately-sized panel, though this may vary depending upon the condition of the paintwork. Apply the wax to the panel with small, overlapping circular strokes, light pressure, and in a consistent pattern to obtain full coverage of the paint. If the applicator feels like it is starting to run dry across the surface, or coverage becomes uneven, return the applicator to the container using another quarter-turn of the pad to re-prime the foam. The goal when waxing is to apply the product as thinly and evenly as possible, since a little bit goes a very long way to protecting and enhancing the shine of your vehicle.

Once you have completed one normal-sized panel, or half of a large one, move on to another section of equal size. When you are done waxing the second section, you will be ready to buff off the wax from the first using a plush microfibre towel. Continue until all panels are complete. Auto-Finesse Desire only takes a few minutes to cure, so take care not to let the product dry onto the surface. If the wax has been allowed to dry, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied.), you can use a water-based quick detailer like Auto-Finesse Finale to help ease removal of the residue. When applying multiple layers of wax for extra depth, wetness and protection, make sure to wait at least 3 hours in between coats.

For best results, do not wax the vehicle if the ambient temperature is below 6 degrees Celsius, or above 35 degrees Celsius. Waxing in direct sunlight, or conditions of high humidity can respectively lead to over, or under-curing of the product before removal.

Related Products

Auto Finesse Desire 150G - Carnauba Wax

Pay Cash On Delivery *

Free delivery **

* Only for Pakistan

** Not valid for tyres or heavy items

Note: Any order above 10 thousand require upfront money using Bank transfer or Easy Paisa

This product is currently sold out.

OUR FLAGSHIP CARNAUBA CAR WAX , CAREFULLY BLENDED BY HAND THERE IS NO FINER WAY TO COMPLETE YOUR FLAWLESS FINISH

The Auto Finesse Desire carnauba natural wax is carefully blended by hand in Great Britain and contains 54% T1 Grade Brazilian Carnauba Wax by volume, with the remainder being made up by all natural Beeswax, and oils. These ingredients treat vehicles with nature’s own defense against the elements, giving it water repellency, and resistance to environmental pollution (Including UV-fading, acid rain, and bird droppings.).

It smells of wild berry and has an ultra-high wax solids content, meaning durability of up to 6 months. 

Application:

Before waxing, make sure that the vehicle is clean and cool to the touch. If bonded contamination is present, use a clay bar to prep the surface for best results. If the paintwork is lightly marred, or the vehicle has not been polished in the last 6-12 months, it is also advisable to use one of our signature Pre-Wax Cleansers in order to create the maximum shine. Place a foam applicator inside the pot of wax, and rotate it half a turn to prime the pad with product. This is typically enough wax to protect a single moderately-sized panel, though this may vary depending upon the condition of the paintwork. Apply the wax to the panel with small, overlapping circular strokes, light pressure, and in a consistent pattern to obtain full coverage of the paint. If the applicator feels like it is starting to run dry across the surface, or coverage becomes uneven, return the applicator to the container using another quarter-turn of the pad to re-prime the foam. The goal when waxing is to apply the product as thinly and evenly as possible, since a little bit goes a very long way to protecting and enhancing the shine of your vehicle.

Once you have completed one normal-sized panel, or half of a large one, move on to another section of equal size. When you are done waxing the second section, you will be ready to buff off the wax from the first using a plush microfibre towel. Continue until all panels are complete. Auto-Finesse Desire only takes a few minutes to cure, so take care not to let the product dry onto the surface. If the wax has been allowed to dry, or ‘secondary hazing’ of the wax occurs (A phenomenon which can sometimes happen in hot or humid climates, especially if the product was over-applied.), you can use a water-based quick detailer like Auto-Finesse Finale to help ease removal of the residue. When applying multiple layers of wax for extra depth, wetness and protection, make sure to wait at least 3 hours in between coats.

For best results, do not wax the vehicle if the ambient temperature is below 6 degrees Celsius, or above 35 degrees Celsius. Waxing in direct sunlight, or conditions of high humidity can respectively lead to over, or under-curing of the product before removal.

comments powered by Disqus